40limit state of collapse : shear

40.1.1 Beams of Varying Depth

In the case of beams of varying depth the equation shall be modified as:

Figure description:

M tan B d bd

where

• $\tau_{\mathrm{v}}, V_{\mathrm{u}}, b$ and $d$ are the same as in 40.1,

$M_{y}$ = bending moment at the section, and

β = angle between the top and the bottom edges

of the beam.

The negative sign in the formula applies when the bending moment $M_{y}$ increases numerically in the same direction as the effective depth $d$ increases, and the positive sign when the moment decreases numerically in this direction.

40.2.1

The design shear strength of concrete in beams without shear reinforcement is given in Table 19.

40.2.1.1

For solid slabs, the design shear strength for concrete shall be $\tau_{k}$, where $k$ has the values given below:

NOTE — This provision shall not apply to flat slabs for which 31.6 shall apply.

40.2.2 Shear Strength of Members under Axial Compression

For members subjected to axial compression $P_{u}$, the design shear strength of concrete, given in Table 19, shall be multiplied by the following factor :

$\delta=1+\frac{3 P_{u}}{A_{g} f_{\mathrm{ck}}}$ but not exceeding 1.5

where

$e$ $P_{u}=$ axial compressive force in Newtons,

• = gross area of the concrete section in mm², and
• $f_{\mathrm{ck}}=$ characteristic compressive strength of concrete.

40.2.3 With Shear Reinforcement

Under no circumstances, even with shear reinforcement, shall the nominal shear stress in beams $\tau_{v}$ exceed $\tau_{\max }$ given in Table 20.

40.2.3.1

For solid slabs, the nominal shear stress shall not exceed half the appropriate values given in Table 20.

Table 19 Design Shear Strength of Concrete, $\tau_{\mathrm{c}}, \mathrm{N} / \mathrm{mm}^{2}$

(Clauses 40.2.1, 40.2.2, 40.3, 40.4, 40.5.3, 41.3.2, 41.3.3 and 41.4.3)

NOTE — The term A, is the area of longitudinal tension reinforcement which continues at least one effective depth beyond the section being considered except at support where the full area of tension reinforcement may be used provided the detailing conforms to 26.2.2 and 26.2.3

Table 20 Maximum Shear Stress, $\tau_{\mathrm{c} \max }, \mathrm{N} / \mathrm{mm}^{2}$

(Clauses 40.2.3, 40.2.3.1, 40.5.1 and 41.3.1 )

Where bent-up bars are provided, their contribution

Where bent-up bars are provided, their contribution towards shear resistance shall not be more than half that of the total shear reinforcement.

Shear reinforcement shall be provided to carry a shear equal to $V_{u}-\tau_{c} b d$ The strength of shear reinforce- ment $V_{u}$ shall be calculated as below:

a) For vertical stirrups:

$\frac{0.87 f_{y} A_{s v} d}{s_{v}}$

b) For inclined stirrups or a series of bars bent-up

• at different cross-sections:

$V_{u s}=\frac{0.8 .7 f_{y} A_{s v} d}{s_{v}}\left(\sin \alpha+\cos \alpha\right)$

• c) For single bar or single group of parallel bars, all bent-up at the same cross-section:

$V_{u s}=0.87 f_{y} A_{s v} \sin \alpha$

where

• $A_{\mathrm{v}}=$ total cross-sectional area of stirrup legs or bent-up bars within a distance $s_{\mathrm{v}}$.
• $s_{v} \quad=$ spacing of the stirrups or bent-up bars along the length of the member,
• $\tau_{y} \quad=$ nominal shear stress,
• = design shear strength of the concrete.
• $b \quad=$ breadth of the member which for flanged beams, shall be taken as the breadth of the web $b_{w}$.
• = characteristic strength of the stirrup or bent-up reinforcement which shall not be taken greater than 415 N/mm².

α

• = angle between the inclined stirrup or bent-up bar and the axis of the member, not less than 45°, and

d

:;

effective depth.

NOTES

• 1 Where more than one type of shear reinforcement is used to reinforce the same portion of the beam, the total shear resistance shall be computed as the sum of the resistance for the various types separately.
• 2 The area of the stirrups shall not be less than the minimum specified in 26.5.1.6.

40.5.1 General

Shear failure at sections of beams and cantilevers without shear reinforcement will normally occur on plane inclined at an angle $30^{\circ}$ to the horizontal. If the angle of failure plane is forced to be inclined more steeply than this [because the section considered $(X-X)$ in Fig. 24 is close to a support or for other reasons], the shear force required to produce failure is increased.

The enhancement of shear strength may be taken into account in the design of sections near a support by increasing design shear strength of concrete to $2 d \tau_{\mathrm{c}} / a_{\mathrm{v}}$ provided that design shear stress at the face of the support remains less than the values given in Table 20. Account may be taken of the enhancement in any situation where the section considered is closer to the face of a support or concentrated load than twice the effective depth, $d$. To be effective, tension reinforcement should extend on each side of the point where it is intersected by a possible failure plane for a distance at least equal to the effective depth, or be provided with an equivalent anchorage.

40.5.2 Shear Reinforcement for Sections Close to Supports

If shear reinforcement is required, the total area of this

is given by:

$A_{x}=a_{y} b\left(\tau_{y}-2 d \tau_{c} / a_{y}\right) / 0.87 f_{y} \geq 0.4 a_{y} b / 0.87 f_{y}$

This reinforcement should be provided within the middle three quarters of $a_{y}$, where $a_{y}$ is less than $d$, horizontal shear reinforcement will be effective than vertical.

40.5.3 Enhanced Shear Strength Near Supports (Simplified Approach)

The procedure given in 40.5.1 and 40.5.2 may be used for all beams. However for beams carrying generally uniform load or where the principal load is located farther than $2 d$ from the face of support, the shear stress may be calculated at a section a distance $d$ from the face of support. The value of $\tau_{\mathrm{c}}$ is calculated in accordance with Table 19 and appropriate shear reinforcement is provided at sections closer to the support, no further check for shear at such sections is required.